? 2006 teledyne relays (800) 284-7007 ? www.teledynerelays.com S20DC100 page 1 S20DC100\062006\q1 new series S20DC100 output to 100a, 200 vdc dc solid-state relay part number description S20DC100 100a, 200 vdc solid-state relay part number explanation electrical specifications (+25c ambient temperature unless otherwise specifed) input (control) specifications min max units control range 4.5 32 vdc input current range 25 42 madc typical turn-on voltage 4.3 vdc must turn-off voltage 1 vdc reverse voltage 32 vdc reverse leakage current 100 a features/benefits ? latest generation mosfet technology ? ultra low on-state resistance ? innovative isolated driver ensures fast power transistor turn on and off and thus low power transient ? ultra low output leakage current ? low control current consumption ? triggered control input to avoid linear control risks ? low conducted and radiated disturbances 20 line voltage 1 100 output current C amps dc switch type 2 s series notes 1) line voltage (peak): 20 = 200 vdc 2) switch type: dc = dc mechanical specification figure 1 tolerances: ?0.3 dimensions in inches (mm) weight: 3.52 oz. (100g) 1+ 2C 4C 3+ 1.10 (28) ?4.7 1.7 (43.2) 1.87 (47.6) 0.29 (7.5) 0.20 (5.1) 1.0 (25.4) 1.75 (44.5) m5 m3 2.29 (58.2) 1.10 (28) ?0.5 0.77 (19.6) 0.89 (22.8) 1.01 (25.8) figure 3 block diagram + 3 control iscst led phv driver (off) mosfet output C 4 1 + 2 + single pulse turn on & off circuit figure 2 control characteristic 45 40 35 30 25 20 15 10 5 0 0 @25c control current (madc) control voltage (v) 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32
S20DC100 page 2 s pecifications are subject to change without notice ? 2006 teledyne relays S20DC100\062006\q1 new series S20DC100 output to 100a, 200 vdc dc solid-state relay electrical specifications (+25c ambient temperature unless otherwise specifed) output (load) specifications min max units operating range 0 130 vdc peak voltage 200 vpeak reverse voltage (internal diode) 1.6 v maximum repetitive avalanche current 100 a maximum single pulse a valanche energy 750 mj maximum repetitive pulse a valanche energy 58 mj maximum nominal currents (resistive) 100 a non-repetitive peak overload current 400 a leakage current 250 adc on-state resistance 22 m output capacitance (t ypical) 1.5 nf j unction-case thermal resistance 0.4 c/w built-in h eat sink thermal resistance (v ertically mounted) 8 c/w h eat sink thermal time constant 10 min control inputs/power outputs insulation voltage 4 kv turn-on time 10 s turn-on delay 600 s turn-off time 10 s turn-off delay 100 s on-off frequency 700 hz figure 4 high side wiring diagram (load connected to ) figure 5 + C dc control power supply vc ic on-off control dc mains (red paths as short as possible.) ie ve c1 d1 d2 or or or load + C vt 4C 3+ 1+ 2C low side wiring diagram (load connected to +) + C dc control power supply vc ic on-off control dc mains ie ve c1 d1 d2 or or or load + C vt 4C 3+ 1+ 2C (red paths as short as possible.) turn-on vc (control) vt (switch) tdon ton t t turn-off vc (control) vt (switch) tdoff toff t t figure 6 time diagrams figure 7 on resistance vs. temperature 25 20 15 10 5 0 C50 rdson (mohms) junction temperature (c) 0 50 100 150
? 2006 teledyne relays (800) 284-7007 ? www.teledynerela ys.com S20DC100 page 3 S20DC100\062006\q1 new series S20DC100 output to 100a, 200 vdc dc solid-state relay please refer to the installation notice for precautions about mounting the device on a heat sink. ambient temperature (c) power dissipation (w) load current (arms) 110 100 90 80 70 60 50 40 30 20 10 0 266 220 178 141 108 79.2 55 35.2 19.8 8.8 2.2 0 0 30 10 20 40 70 50 60 80 110 90 100 1.1c/w 0.9c/w 0.75c/w 0.55c/w 0.3c/w 0.1c/w 0.3c/w 8c/w 4c/w 2.4c/w 2.2c/w 2.1c/w 1.95c/w 1.5c/w 1.3c/w 1.2c/w power dissipation and load current limit vs. temperature figure 8 general specifications (+25c ambient temperature unless otherwise specifed) environmental specifications min max units operating temperature C40 +90 c storage temperature C40 +100 c input-output isolation 4000 vrms insulation resistance 1 g insulation capacitance <8 pf j unction t emperature 175 c connections po wer control scre wdriver phillips nr2 phillips nr1 tightening t orque 1.8 n.m 0.8 n.m insulated crimp terminals (round t abs, eyelet type) m5 m3 miscellaneous displa y g reen led (on) h ousing ul94v0 mounting 2 screws (m4x12mm) noise le vel no audible noise notes 1. for additional/custom options , contact factory. figure 9 protective cover available add -14 to part number general standards iec60947-1 protection lev el ip00 protection against direct t ouch none ce marking yes e.m.c. emission radiated & conducted disturbances nfen55011
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: teledyne relays: ? S20DC100
|
